-
ASTM D3244 Standard Practice for Utilization of Test Data to Determine Conforman
ASTM D3244 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications5. Sampling5.1 Sampling should be carried out in accordance with standard sampling procedures for petroleum products (Practice D4057 and Practice D4177). Obtain enough sample to allow all required determinations ...
-
ASTM D3244 Standard Practice for Utilization of Test Data to Determine Conforman
ASTM D3244 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications4. Significance and Use4.1 This practice provides a means whereby the parties to a transaction can resolve potential disputes over those product properties which can be tested and expressed numerically.4.1.1 ...
-
ASTM D3244 Standard Practice for Utilization of Test Data to Determine Conforman
ASTM D3244 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications1. Scope1.1 This practice covers guidelines with which two parties, usually a supplier and a receiver, can compare and combine independently obtained test results whenever there is a product quality ...
-
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils9. Report9.1 Report the 0.6 Pa•s (6 P) temperatures as the handling point. Record to the nearest 0.1°C (0.2°F).9.2 Report the 2.5 Pa•s (25 P) temperature as the storage point. If the 25 P temperature was not reached at 4°C (39°F), ...
-
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils8. Procedure8.1 Fill the oil cup with the sample at a temperature not exceeding 82°C (180°F) to a depth of 60 mm (2 1/4 in.). Gently slide the oil container back onto the viscometer and lock in position with the cap. Place the assembly in ...
-
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils6. Apparatus6.1 Thermometers, conforming to ASTM thermometers 63C, 64C, and 12C, or equivalent.6.2 Oil Container, made of aluminum or aluminum alloy to the dimensions given in Fig. 1A and B. The cup (Fig. 1A) is a loose fit on the Model VW ...
-
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils4. Summary of Test Method4.1 A sample of the oil, preheated if necessary to a specified temperature to make it fluid, is poured into the cup of the portable viscometer. This is immersed in a bath at a predetermined temperature. After 15 min, ...
-
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils
ASTM D3245 Test Method for Pumpability of Industrial Fuel Oils1. Scope1.1 This test method is intended for use on petroleum fuel oils, such as those covered in Specification D396 Grade No 4(Light), 4, 5(Light), 5, and 6, or similar fuels.1.2 The values stated in SI units are to be regarded as standard. ...
-
ASTM D3340 Test Method for Lithium and Sodium in Lubricating Greases by Flame Ph
ASTM D3340 Test Method for Lithium and Sodium in Lubricating Greases by Flame Photometer9. Calculation and Report9.1 Calculate the lithium content of the grease as follows:Lithium, mass % = X/100 Wwhere:X = lithium content of the water extract, mg/L lithium (see 8.7), andW = mass of the grease taken, ...
-
ASTM D3340 Test Method for Lithium and Sodium in Lubricating Greases by Flame Ph
ASTM D3340 Test Method for Lithium and Sodium in Lubricating Greases by Flame Photometer8. Procedure8.1 Weigh to the nearest 1 mg approximately 1 g of the grease into a platinum dish or crucible. Heat the dish until the sample can be ignited with a flame. Maintain at such a temperature that the sample ...
