-
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants9. Procedure A - For Resin-Bonded Coatings9.1 Immerse the panels in a beaker of water to a depth of half the length of the panel for 24 h at room temperature. Take care to ensure that the panels are separated.9.2 Remove panels and wipe ...
-
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants6. Apparatus6.1 Rubber Covered Steel Roller - A steel roller, 82.6 +/- 2.5 mm (3.25 +/- 0.1 in.) in diameter and 44.5 +/- 1.3 mm (1.75 +/- 0.05 in.) in width, covered with rubber approximately 6.4 mm (1/4 in.) in thickness having a ...
-
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants4. Summary of Test Method4.1 The dry solid film lubricant is applied to anodized aluminum panels, immersed in water or other fluids for 24 h, and then wiped dry. A strip of masking tape is pressed onto the panel and removed abruptly. ...
-
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants
ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants1. Scope1.1 This test method covers the measurement of the adhesion characteristics of dry solid film lubricants.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information ...
-
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fue
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fuels and Solvents (Doctor Test)8. Procedure8.1 Shake vigorously together in a test tube 10 mL of the sample being tested and 5 mL of sodium plumbite solution for about 15 s. Add a small amount of pure, sublimed flowers of sulfur ...
-
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fue
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fuels and Solvents (Doctor Test)6. Reagents and Materials6.1 Purity of Reagents - Reagent grade chemicals shall be used in all tests. Unless otherwise indicated, it is intended that all reagents conform to the specifications ...
-
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fue
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fuels and Solvents (Doctor Test)3. Summary of Test Method3.1 The sample is shaken with sodium plumbite solution, a small quantity of powdered sulfur added, and the mixture shaken again. The presence of mercaptans or hydrogen ...
-
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fue
ASTM D4952 Test Method for Qualitative Analysis for Active Sulfur Species in Fuels and Solvents (Doctor Test)1. Scope1.1 This test method covers and is intended primarily for the detection of mercaptans in motor fuel, kerosine, and similar petroleum products. This method may also provide information ...
-
ASTM D3242 Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D3242 Standard Test Method for Acidity in Aviation Turbine Fuel11. Report11.1 Report the result to the nearest 0.001 mg KOH/g as Acid Number (Test Method D3242) = (Result).12. Precision and Bias12.1 Precision - The precision of this test method as determined by statistical examination of interlaboratory ...
-
ASTM D3242 Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D3242 Standard Test Method for Acidity in Aviation Turbine Fuel8. Procedure8.1 Introduce 100 g +/- 5 g of the sample weighed to the nearest 0.5 g, into a 500 mL wide-mouth Erlenmeyer flask. (One type of suitable modified flask is shown in Fig. 1.) Add 100 mL of the titration solvent and 0.1 mL of ...
