-
ASTM D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester
ASTM D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester (Ramp Method)6. Apparatus6.1 Flash Point Apparatus - The apparatus consists of an electrically heated test cup that is controlled automatically to give a temperature increase of 2.0 °C/min +/- 0.5 °C/min, a lid and shutter ...
-
ASTM D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester
ASTM D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester (Ramp Method)4. Summary of Test Method4.1 A 2 mL +/- 0.1 mL test specimen is introduced into the test cup that is then heated automatically at a constant rate of 2 °C/min +/- 0.5 °C/min. A gas test flame is directed through ...
-
ASTM D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester
ASTM D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester (Ramp Method)1. Scope1.1 This test method covers the determination of the flash point of aviation turbine fuel, diesel fuel, kerosine and related products in the temperature range of 40 °C to 135 °C by a small scale closed ...
-
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 110. Report10.1 Report whether or not burning as defined in 3.1.1 occurs at the test temperature.10.2 If no burning occurs, report that the Flammability Hazard Rating of the sample is zero (F=0) provided ...
-
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 19. Procedure9.1 Rinse interior of planchet with mineral spirits, wipe drywith absorbent tissue.9.2 Set the control transformer to bring the interior surface of the planchet to 1500°F. Adjust the transformer ...
-
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 16. Test Specimen6.1 Liquid Sample - 30 mL is sufficient for the performance of this test method.6.2 Solid Specimens - 30 g are sufficient for the performance of this test method.7. Apparatus7.1 Flask Heater, ...
-
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 14. Summary of Test Method4.1 Small, measured amounts of the sample are placed on a stainless steel surface heated to 1500°F (815.5°C). Reactions which occur during the 5 min interval, thereafter, are observed ...
-
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings
ASTM D6668 Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 11. Scope1.1 This test method covers a means for the discrimination between solid and liquid materials which will not burn in air when exposed to a temperature of 1500°F (815.5°C) for a period of 5 min ...
-
ASTM D6824 Standard Test Method for Determining Filterability of Aviation Turbin
ASTM D6824 Standard Test Method for Determining Filterability of Aviation Turbine Fuel10. Report10.1 Report the following information:10.1.1 The source and how the sample was obtained, as required in 7.1.10.1.2 The temperature recorded in 9.4 and, if applicable, undissolved water present, and filtration ...
-
ASTM D6824 Standard Test Method for Determining Filterability of Aviation Turbin
ASTM D6824 Standard Test Method for Determining Filterability of Aviation Turbine Fuel9. Procedure9.1 Measure the temperature (see 6.3.3) of the fuel in the transfer container (see 7.2) and, if necessary, adjust to 15 to 25°C.9.2 Shake the sample or transfer container (see 7.2) vigorously for approximately ...
