-
WEAR CHARACTERISTICS OF NON-PETROLEUM AND PETROLEUM HYDRAULIC FLUIDS: ASTM D7043
WEAR CHARACTERISTICS OF NON-PETROLEUM AND PETROLEUM HYDRAULIC FLUIDS: ASTM D7043EXPLANATIONThis test method is an indicator of the wear characteristics of petroleum and non-petroleum hydraulic fluids operating in a constant volume vane pump. Excessive wear in vane pumps could lead to malfunction of hydraulic ...
-
WEAR CHARACTERISTICS OF PETROLEUM HYDRAULIC FLUIDS: ASTM D6973
WEAR CHARACTERISTICS OF PETROLEUM HYDRAULIC FLUIDS: ASTM D6973EXPLANATIONThis test method is an indicator of the wear characteristics of petroleum hydraulic fluids operating in a constant volume vane pump. Excessive wear in vane pumps could lead to malfunction of hydraulic systems in critical industrial ...
-
WAX CONTENT OF CORRUGATED PAPERBOARD: ASTM D3344
WAX CONTENT OF CORRUGATED PAPERBOARD: ASTM D3344EXPLANATIONMany of the functional properties of wax-treated corrugated paperboard and cartons are dependent on the amount of wax present. In the case of the wax-saturated or wax-impregnated paperboard, the principle concern is with the weight of wax used ...
-
WAX APPLIED DURING CURTAIN COATING OPERATION: ASTM D3708
WAX APPLIED DURING CURTAIN COATING OPERATION: ASTM D3708EXPLANATIONWax coatings are applied to corrugated board to provide a barrier against moisture or other penetrates or to provide improved appearance or abrasion resistance. These functional properties are influenced by the amount of wax present on ...
-
WAX APPEARANCE POINT OF DISTILLATE FUELS: ASTM D3117
WAX APPEARANCE POINT OF DISTILLATE FUELS: ASTM D3117EXPLANATIONWax appearance point is the temperature at which wax crystals begin to precipitate out of a fuel under specified cooling conditions. The presence of wax crystals in the fuel may restrict flow or plug the fuel filter. In critical fuel systems, ...
-
WATER WASHOUT CHARACTERISTICS OF LUBRICATING GREASES: ASTM D1264
WATER WASHOUT CHARACTERISTICS OF LUBRICATING GREASES: ASTM D1264(Equivalent Test Methods: IP 215, ISO 11009, and DIN 51807 T2)EXPLANATIONThis test method covers the evaluation of the resistance of a lubricating grease to washout by water from a bearing, when tested at 38 and 79° C (100 and 175° F) ...
-
WATER UNDISSOLVED IN AVIATION TURBINE FUELS: ASTM D3240
WATER UNDISSOLVED IN AVIATION TURBINE FUELS: ASTM D3240EXPLANATIONUndissolved (free) water in aviation fuel can encourage the growth of microorganisms and subsequent corrosion in the tanks of aircraft and can also lead to icing of filters in the fuel system. The usual range of the test reading covers ...
-
WATER TOLERANCE OF GASOLINE-ALCOHOL BLENDS: ASTM D6422
WATER TOLERANCE OF GASOLINE-ALCOHOL BLENDS: ASTM D6422EXPLANATIONGasoline-alcohol blends have a very limited ability to retain water in solution or in a stable suspension, and if the amount of water in the blend exceeds this limit, the fuel will separate into a lower aqueous and an upper hydrocarbon ...
-
WATER IN SOLVENTS BY KARL FISCHER TITRATION: ASTM D1364
WATER IN SOLVENTS BY KARL FISCHER TITRATION: ASTM D1364EXPLANATIONThis test method covers the determination of water in any proportion in volatile solvents and chemical intermediates used in paint, varnish, lacquer, and related products.This test method is not applicable in the presence of mercaptans, ...
-
WATER SOLUBILITY IN HYDROCARBONS AND ALIPHATIC ESTER LUBRICANTS: ASTM D4056
WATER SOLUBILITY IN HYDROCARBONS AND ALIPHATIC ESTER LUBRICANTS: ASTM D4056EXPLANATIONThis test method covers a procedure for estimating the equilibrium solubility of water and its vapor in hydrocarbon and aliphatic ester lubricants, at temperatures between 277 and 373 K. This test method is limited ...