-
ASTM D2570 Test Method for Simulated Service Corrosion Testing of Engine Coolant
ASTM D2570 Test Method for Simulated Service Corrosion Testing of Engine Coolants5. Apparatus5.1 Reservoir - An assembly drawing of this component is shown in Fig. 1. The material ofconstruction, representing that ofthe engine cylinder block, shall be SAE G3500 Gray Iron for Automotive Castings. Install ...
-
ASTM D2570 Test Method for Simulated Service Corrosion Testing of Engine Coolant
ASTM D2570 Test Method for Simulated Service Corrosion Testing of Engine Coolants3. Summary of Test Method3.1 An engine coolant is circulated for 1064 h at 190°F (88°C) in a flow loop consisting of a metal reservoir, an automotive coolant pump, an automotive radiator, and connecting rubber hoses. Test ...
-
ASTM D2570 Test Method for Simulated Service Corrosion Testing of Engine Coolant
ASTM D2570 Test Method for Simulated Service Corrosion Testing of Engine Coolants1. Scope1.1 This test method evaluates the effect of a circulating engine coolant on metal test specimens and automotive cooling system components under controlled, essentially isothermal laboratory conditions.1.2 This test ...
-
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion C
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants10. Precision and Bias10.1 The precision of this test method is based on interlaboratory study of Test Method D2809, conducted in 2008. Each of four laboratories tested ...
-
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion C
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants8. Procedure8.1 Before each test is begun, clean the test apparatus as follows:8.1.1 Remove and replace all hose (hose shall not be used for more than one test), set the ...
-
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion C
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants5. Apparatus5.1 Pump Test Stand - Detailed drawings are available. The copper, brass, and bronze flow circuit is illustrated in Fig. 1. The apparatus should be assembled ...
-
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion C
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants3. Summary of Test Method3.1 This test method consists of pumping an aqueous coolant solution at 113°C (235°F) through a pressurized 103-kPa (15-psig) simulated automotive ...
-
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion C
ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants1. Scope1.1 This test method covers the evaluation of the cavitation corrosion and erosion-corrosion characteristics of aluminum automotive water pumps with coolants.NOTE ...
-
ASTM D4340 Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine
ASTM D4340 Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions15. Report15.1 Report the following information:15.1.1 Report the heat-transfer corrosion rate to the nearest 0.1 mg/cm2/week of each specimen.15.1.2 The appearance of each specimen, ...
-
ASTM D4340 Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine
ASTM D4340 Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions11. Procedure11.1 Assembly - Assemble the cell in accordance with Fig. 1. Use new O-rings between the aluminum test specimen and glass cell for each test. To help ensure that the O-rings ...
