-
ASTM D3240 Test Method for Undissolved Water In Aviation Turbine Fuels
ASTM D3240 Test Method for Undissolved Water In Aviation Turbine Fuels1. Scope1.1 This test method covers the measurement of undissolved water in aviation turbine fuels in flowing fuel streams without exposing the fuel sample to the atmosphere or to a sample container. The usual range of test readings ...
-
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)8. Report8.1 Report as the color the number of the standard that most nearly matches the specimen. In the event that the color lies midway between two standards, report the darker of the two.8.2 If, owing to differences in hue between ...
-
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)4. Apparatus4.1 Spectrophotometer, equipped for liquid samples and for measurements in the visible region.NOTE 2 - The spectrophotometer used must be clean and in first-class operating condition. The instrument should be calibrated ...
-
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)3. Significance and Use3.1 The property of color of a solvent varies in importance with the application for which it is intended, the amount of color that can be tolerated being dependent on the color characteristics of the material ...
-
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)1. Scope1.1 This test method describes a procedure for the visual measurement of the color of essentially light colored liquids (Note 1). It is applicable only to materials in which the color-producing bodies present have light ...
-
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids18. Report18.1 State that the test was conducted in accordance with Test Method D471 and report the following:18.1.1 Description of the sample and its origin,18.1.2 Date and temperature of testing room (see 5.1),18.1.3 Duration, temperature, ...
-
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids17. Calculation17.1 Calculate the percent change in mass as follows (Section 10):17.2 Calculate the percent change in volume as follows (Section 11):17.3 Calculate the percent change in dimensions as follows (Section 12):17.4 Calculate ...
-
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids10. Procedure for Change in Mass10.1 Test three specimens of a single composition. Calculate the test results of the three specimens (see 17.1, Eq 1) and average the results. Weigh each specimen in air to the nearest 1 mg, record the ...
-
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids8. Apparatus8.1 For non-volatile liquids, a glass test tube, having an outside diameter of 38 mm (1.5 in.) and an overall length of 300 mm (12 in.) fitted loosely with a stopper (see 8.2.1) shall be used. Glass beads shall be used ...
-
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids
ASTM D471 Standard Test Method for Rubber Property - Effect of Liquids5. Test Conditions5.1 Temperature and Immersion Periods - Unless otherwise specified the test temperature and immersion period shall be as indicated in Table 1, depending upon the anticipated service conditions:5.1.1 When the temperature ...
